Performance The R105 is built for efficiency. Super Hi-Power drive chains feature heavy, high-strength construction designed for the most rugged conditions. Longer wheelbase and a low center-of-gravity offer a smooth, stable ride. Hydraloc™ automatic interlock system locks lift, tilt and drive systems when the operator leaves the seat, increasing operator safety. System also engages when the restraint bar is raised or the ignition switch is turned off. Lift arm hydraulic tubes are concealed and protected from the work environment. Rated operating load can be readily increased with the addition of a counterweight. Overall Width (mm) 48.4" (1229) Overall Height to Top of ROPS (mm) 70.3" (1786)
Operator's Cabin A large operator’s compartment with clear front, side and rear sight lines provides operators full, expansive views for increased safety. ROPS/FOPS Level II is standard for extra operator protection. Roof grid section and window provide excellent bucket visibility at full height. Adjustable operator restraint bar offers secondary protection and serves as a padded armrest. Lockout system shuts down lift/tilt functions when optional front door is opened. Open canopy, open canopy with door and enclosed cab with heat are available.
Controls Ergonomic controls in the R105 Skid Loader provide smooth loader and attachment operation. Hand and foot throttle are standard equipment, providing quieter operation and less fuel consumption T-Bar hands-only drive control system
Engine Equipped with a powerful 33.1 hp (24.7) Yanmar diesel engine, the R105 Skid Loader can tackle any challenge. Liquid-cooled for superior performance in all weather conditions. Excellent cold weather starting with glow plug assist system. Make Yanmar Model 3TN88CKMS Tier IV Net Power (kW) @ rpm 33.1 (24.7) @ 2800 Maximum Torque (Nm) @ rpm 80 ft. - lbs. (108) @ 1680 Displacement (L) 100 cu. in. (1.6)
Hydraulics The R105 provides 14.5 gpm (55) of hydraulic flow powering a variety of attachments to get work done faster. Direct-drive hydrostatic pump with self-neutralizing feature provides 100% efficient drive from engine to pump, requiring no maintenance Hydraloc™ Automatic Interlock System increases operator safety by locking lift, tilt and drive systems when the operator leaves the seat, raises the restraint bar or turns off the ignition switch. Auxiliary Hydraulics - Standard (L/min) 14.5 gpm (55) High-Flow Auxiliary Hydaulics - Option NA Reservoir Capacity (L) 8 gal. (30.3)
Attachment System A full line of Edge attachments and accessories are designed specifically to fill operators’ needs, making their R105 the most versatile machine on the job site. Popular attachments are listed below. A Augers B Bale Movers C Blades D Brooms E Grapples F Pallet Forks G Rakes H Snow Removal Full Line of Edge Attachments for R105
Lift Arm Strong lift arm provides strength, durability and excellent view of the tires and sides of the loader for increased precision and safety.
Serviceability The R105 has an ingenious design, including low-maintenance components and easy maintenance access. Entire ROPS/FOPS structure pivots back, with gas-spring assist, for full, easy access to the internal hydraulic components. Swing-open rear door and flip-up engine cover fully expose maintenance access points to engine, battery, filters and filler caps. Maintenance-free axles are lubricated and sealed for long life. Removable access plates for clean out.
Specifications (standard) Dimensions A Overall Operating Height - Fully Raised 139.6" B Height to Hinge Pin - Fully Raised 107.5" C Overall Height to Top of ROPS 70.3" D Overall Length with Bucket 114" E Dump Angle at Full Height 42° F Dump Height 84.5" G Dump Reach at Full Height 22.8" J Rollback at Ground 29° M Rollback Angle at Full Height 99° O Seat to Ground Height 32.6" P Wheelbase 34.5" Q Overall Width - Less Bucket A 48.4" R Bucket Width 55" S Ground Clearance to Chassis 6.0" V Overall Length - Less Bucket 88.9" W Departure Angle 26° X Clearance Circle – Front w/ Bucket 69.4" Y Clearance Circle – Front w/o Bucket 44.1" Z Clearance Circle – Rear 54.1" Standard Specification Tire Size 27x8.5x15 HD Engine Make Yanmar Model 3TNV88C-KMS Tier IV Gross Power @ 2500 rpm 34.7 hp Net Power @ 2500 rpm 33.1 hp Maximum Torque 80.7 ft.-lbs. @ 1820 Displacement 100 cu.in. Hydraulic System Auxiliary Hydraulics - Standard 14.5 gpm High-Flow Auxiliary Hydraulics - Option N/A Reservoir Capacity 8 gal. Electrical System Battery 12-volt Starter 12-volt Alternator 40-amp Capacities/Weights Rated Operating CapacityB 1,050 lbs. Rated Operating Capacity with Optional CounterweightB 1,175 lbs. Fuel Tank 10.4 gal. Travel Speed - Maximum 5.9 mph Travel Speed with Two-Speed Option - Maximum N/A Operating WeightC - Approximate 4,000 lbs. A - Overall width is dependent upon the amount of wheel offset. B - Per SAE J818, SAE J732, and ISO 14397 C - Weight of base unit with standard equipment, standard tires (heavy-duty flotation), standard dirt-construction bucket and 79 kg operator.
Specifications (metric) Dimensions A Overall Operating Height - Fully Raised 3546 mm B Height to Hinge Pin - Fully Raised 2731 mm C Overall Height to Top of ROPS 1786 mm D Overall Length with Bucket 2896 mm E Dump Angle at Full Height 42° F Dump Height 2146 mm G Dump Reach at Full Height 579 mm J Rollback at Ground 29° M Rollback Angle at Full Height 99° O Seat to Ground Height 828 mm P Wheelbase 876 mm Q Overall Width - Less Bucket A 1229 mm R Bucket Width 1404 mm S Ground Clearance to Chassis 152 mm V Overall Length - Less Bucket 2258 mm W Departure Angle 26° X Clearance Circle – Front w/ Bucket 1763 mm Y Clearance Circle – Front w/o Bucket 1120 mm Z Clearance Circle – Rear 1374 mm Standard Specification Tire Size 27x8.5 x 15 HD Engine Make Yanmar Model 3TNV88C-KMS Tier IV Gross Power @ 2500 rpm 25.5 kW Net Power @ 2500 rpm 24.7 kW Maximum Torque 109.4 Nm @ 1820 Displacement 1.6 L Hydraulic System Auxiliary Hydraulics - Standard 55 L/min High-Flow Auxiliary Hydraulics - Option N/A Reservoir Capacity 30.3 L Electrical System Battery 675 CCA Starter 2.3 kW Alternator 40-amp Capacities/Weights Rated Operating CapacityB 476 kg Rated Operating Capacity with Optional CounterweightB 533 kg Fuel Tank 39.4 L Travel Speed - Maximum 9.5 km/hr Travel Speed with Two-Speed Option - Maximum N/A Operating WeightC - Approximate 1814 kg A - Overall width is dependent upon the amount of wheel offset. B - Per SAE J818, SAE J732, and ISO 14397 C - Weight of base unit with standard equipment, standard tires (heavy-duty flotation), standard dirt-construction bucket and 79 kg operator.
Options Controls T-Bar Hand Controls Available Standard Hand/Foot Controls Available Standard Joystick Controls Available Dual-Hand Controls Available Engine Engine Auto-Shutdown System Engine Heater Optional Turbocharged Engine Hydraulics Auxiliary Hydraulics Standard High-Flow Auxiliary Hydraulics Operator Station Cab Enclosure Optional Foot or Hand-Controlled Throttle Standard Full Instrumentation Standard Heater Optional Horn Optional Integral Access Plate (Removable) Standard Restraint Bar with Padded Armrests/Seat Belts ROPS/FOPS Level II Overhead Guard, Integral Side Screens Standard Sound Reduction Package Suspension Seat - Mechanical Optional Work Lights, Front and Rear Standard Performance All-Tach® Attachment Mounting System Standard Anti-Vandalism Protection Standard Back-Up Alarm Optional Brake Control (Auto/Manual) Standard Hydraglide™ System Hydraloc™ System Standard Hydrostatic Drive Standard Lift Arm Support Device Standard Self-Leveling Lift Action Optional Two-Speed Drive
Warranty Gehl stands behind its products with a powerful warranty program. We know that Gehl equipment is put to the test each day, and we engineer and build our equipment to stand up to the challenges they face. To back up our commitment to quality, all Gehl equipment is backed by a twelve month warranty. An extended warranty is available for additional protection to your investment. Read more by clicking on the link to our warranty page below. Gehl Warranty